Category Archives: Fix Netgear Error

18May/19

Confronting Netgear Authentication Problem? Get Ultimate Steps To Resolve It

Keeping the Wi-Fi connection on the Netgear router protected is essential for the integrity of the system and the information saved on it. Hence, it’s better to configure the Netgear router correctly so that the broadcast signal is encrypted. When encryption is enabled, then only those users can authenticate with the router who has the proper login credentials. Therefore, set the Netgear router to broadcast authentication by generating an encryption code using the Web-based interface. This authentication process is not free from random flaws. Netgear authentication problem is a common problem faced by several users while trying to connect devices like smartphones, laptops even after providing the proper login credentials.

Therefore, if you also face the same issue, then nothing to get worried about this. Here in this article, we are going to provide some of the possible ways which can help you to fix the authentication problems of your Netgear router. Hence, you are advised to go through the article given below. So, let’s start.

Know the Root Causes of Netgear Authentication Problem:

Before implementing the solutions, it is essential to know the probable causes behind the problem. It also becomes easy to fix an issue when you know the specific reason behind its occurrence. So, let’s have a look at the points mentioned below:

  • This problem can happen when there is a problem with the configuration settings of the router.
  • You can also face the Netgear router authentication problem if the login credentials you have provided does not suit with the original ones.
  • If the router’s firmware is out-of-date, then it also might be the reason behind this issue.  
  • If there is any problem with the hardware of the router, then you can also encounter this error.

Now, you are aware of the probable causes behind this problem. Hence, you just need some hacks to fix the Netgear authentication problem.

Easy Tips and Tricks to Fix the Netgear Router Authentication Problem

There are a lot of ways to fix this Netgear authentication problem. Hence, you need to have a glance at the troubleshooting hacks explained below:

Procedure 1: Update the Firmware of the Netgear Router

You might face the Netgear authentication problem if you do not update the firmware of the router since a while. Thus, it is better to fix this problem by updating the firmware of your Netgear router. Here are the steps what you have to do:

  1. At first, launch your default web browser. Then, you need to go to the official website of Netgear.
  2. Now, move the cursor to the search field and type the model number of your Netgear router to fix it with ‘firmware.’
  3. On the next window, scroll down the list of the firmware and find the specific one for your device. You will now easily find it using the model number of your router.  
  4. Next, you should download the latest firmware for your router device. When the downloading process completes, install it by following the on-screen guidance.

Once the installation process finishes, you need to restart the router to inspect whether the issue is still in the same position or not. If the issue persists, then you should move on to further methods.

Procedure 2: Reset the Wi-Fi Connection

According to some users, they have fixed the Netgear router authentication problem by resetting the broadcast connection. To correct this problem, you should perform the steps as follows:  

  1. At first, hit the I and Windows key both at the same time from the keyboard to open the Settings window. Else, you can also go to the Start menu and tap on the gear-shaped Settings icon.  
  2. On the next window, navigate to the ‘Network & Internet’ section. Now, choose the ‘Wi-Fi’ option under the ‘Network & Internet’ window.
  3. Next, tap on the ‘Show available networks’ option from the same window. As a result, it will show a complete list of the Wi-Fi networks that are detected by the system previously. Select any of the networks that you wish to connect from the current page.
  4. After that, right-click on the selected Wi-Fi network and choose the ‘Forget’ option from the list.
  5. To find the network and connect it you should turn the ‘Wi-Fi’ off by going to the ‘Settings’ window. Then, enter the login credentials to connect the Wi-Fi network.

After completing the above process, restart the router and check if the issue has been resolved or not. If you see that the issue still appears, then perform the further procedure discussed below.

Procedure 3: Change the Configuration Settings of the Broadcast Network

You can encounter the Netgear authentication problem also due to an incorrect IP address. Hence, you should change the configuration settings of the broadcast network to fix this problem. To do that, you need to follow the steps mentioned below:

  1. First, move the cursor to the bottom left corner of the window and tap on the Start logo. Then, tap on the gear-shaped Setting icon located above the ‘Power’ icon. It will open the ‘Settings’ window.
  2. Go to the ‘Network & Internet’ section under the Settings window. Look at the left side of the window and tap on the ‘Wi-Fi’ option. Now, on the next window, tap on the ‘Change adapter’ option by going to the ‘Related settings’ window.
  3. Next, you have to select the network adapter that is connected currently with the system and right-click on it. Then, select the ‘Properties’ option from the popup list. It will navigate you to the ‘Wi-Fi Properties’ window. Now, you will see the ‘Internet Protocol Version 4 (TCP/IPv4)’ option on the list. Click twice on it.
  4. On the next window, you will see the same option named by ‘Internet Protocol Version 4 (TCP/IPv4) Properties.’ Tap on it. Now, you should select the ‘Obtain an IP address automatically’ option. After that, click on the ‘Obtain DNS server address automatically’ option.
  5. Now, tap on the OK button. Press the Alt and F4 key simultaneously from the keyboard to exit from the current window.

After that, restart the system to apply the changes. Now, you should try to connect the Wi-Fi network to check whether the issue has been fixed or not. If the problem still persists, then go to the next solution.

Procedure 4: Change the Wrong Credentials of the Wi-Fi Network

If you enter wrong passwords which do not suit the present database, then you can meet the ‘Netgear authentication problem’ issue. To fix this problem, you have to follow the steps given below:  

  1. At first, select the broadcast network where you have entered the incorrect login credentials by going to the Wi-Fi icon on the taskbar.
  2. After that, right-click on the Wi-Fi icon and tap on the ‘Forget’ option to eliminate the login credentials of the wireless network.
  3. Now, turn the Wi-Fi network off and then wait for a few minutes. Then, turn the Wi-Fi network on. Pick the broadcast network from the list which you prefer to connect.
  4. Next, you have to enter the password of the login credential which is ‘Password’. Try to enter the right password to connect with the broadcast network.

After that, you should restart the system to save the changes. Try to connect the network to check whether the issue persists or not. If the issue still appears, then perform the further procedure.

Procedure 5: Perform a Factory Reset of the Netgear Router

After trying all the solutions above, if you are still not able to connect the system with the wireless network, then the last option that you should perform is a factory reset of your Netgear router. To perform this, you should follow the steps given below:

  1. While turning the router on, you should go back side of the router. There you will see a hole or small button labeled by ‘Reset.’
  2. After that, either insert a clip on the hole or click the button. Hold it for at least 10 seconds until you will see that the ‘Power’ light started to blink.
  3. After waiting 10 seconds, you should release it. Now, wait until the ‘Power’ light to become stable.
  4. Once the power light is stable, it indicates that the router is set to the default settings. Hence, now you can easily adjust the configuration settings as you wish.  

After that, restart the router and try to connect with the system to check whether the ‘Netgear authentication problem’ issue is resolved.

Final Recommendation

In the above guide, we have discussed some of the possible ways to fix the Netgear authentication problem. We hope if you implement the above-mentioned ways in their corresponding order, then it will definitely help you to put an end to this bug. After successfully performing the above methods, if you are still facing any other kinds of trouble, then you need to seek help from a tech expert for further assistance. In addition, you can also share your queries and valuable feedback through the comment box given at the end of this post.

17May/19

Netgear Error 1605: Resolve The Issue With Some Simple Steps

Among all well-known router brands, Netgear is the best one. It is capable of delivering brilliant performance. Irrespective of its excellent features, you can still get some issue over time. And, one such issue that you face is the Netgear error 1605. Once this error code occurs, you will not be able to access the device. Therefore, you need to resolve it right away.

In this article, you will get the steps that will help you to resolve the Netgear issue. Here, we will discuss some of the causes too that will help you to fix error 1605. Therefore, keep reading this article.

Possible Reasons behind the Netgear Error 1605

Knowing the causes will help you to understand work. Therefore, have a look at the causes responsible for error 1605:

  1. The most common reason is an issue with the internet connection.
  2. In addition to that, if there is an issue with the firmware of the Netgear router, then you get this error.
  3. If the Router Driver is out of date or corrupted, then also you encounter this error code.
  4. In case there is an issue with the sign-in process, then also you encounter this problem.
  5. Another reason that can be responsible for this r error code is dirt and dust accumulation.

Methods to Resolve the Netgear Genie Error 1605

There are some easy methods that you can try to fix this error code 1605. You have to perform all the steps carefully without skipping any. Therefore, look at the methods discussed below:

Method 1: Power Restart the Netgear router

You can resolve most of the minor errors of the Netgear routers by restarting it. Hence, follow the steps given here:

  • Press and hold down the Power button of your Netgear router. Wait till all the lights go off and the router completely turns off.
  • Once the router turns off, unplug the power cord from the power outlet.
  • After that, unplug the Ethernet cable from the system and the router.
  • Now, you have to wait for 5 to 10 minutes and then plug in the power cord.
  • Again, press and hold down the Power button of the router. This will turn on the Netgear router.
  • As the Netgear router turns on, you have to connect it to the system.
  • After that, check if the Netgear error 1605 is still there or not.

Method 2: Reset the Netgear Router to its Default Settings

You can also reset the Router Settings to its default. Doing so can eliminate this error code. Hence, have a look at the points that we have provided below:

  • First of all, switch off the Netgear router by pressing the Power button. Now, unplug the Power cord from the power outlet.
  • After that, you have to unplug the Ethernet cable from both the computer and the modem.
  • Now, plug in the power cable of the Netgear router to the power outlet. After that, you have to turn on the device.
  • Take a paper clip and press the Reset button. You will find it on the back side of the router.
  • Now, keep pressing the reset button till the power light of the Netgear router becomes steady.
  • Plug in the Ethernet cable to the computer and the modem.
  • Next, you have to open the Netgear router’s home page. Login by using the default username and password. The default username and password will be printed at the back of the Netgear router.
  • After doing all this, you have to check if the Netgear error 1605 is still there or not.

Method 3: Update the Netgear Router Driver

In case the Netgear Router Driver is out of date, then a number of issues can occur. Hence, update the Router Driver to its latest version. Perform the steps that are given below:

  • At first, you have to connect the Netgear router to the computer. After that, open Device Manager from the Start menu.
  • As the Device manager window opens, you have to search for the Netgear Router Driver. On finding, right-click on it.
  • After that, click on the Update driver software from the list of options.
  • Now, click on the first option. After that, you have to wait for the driver update process to complete.
  • Once the driver update finishes, restart both the system and the Netgear router.
  • After that, check if the Netgear error 1605 still occurs or not.

Method 4: Update the Firmware of the Netgear Router

The firmware is important as it is responsible for the performance of the router. Therefore, in order to fix this issue, update the firmware to its latest version. Follow the steps given below:

  • First of all, launch any web browser. Here, we recommend that you connect the Netgear router to the system by using an Ethernet cable.
  • Once the web browser window opens, type 192.168.1.1 in the address bar. After that, hit the Enter key form the system’s keyboard.
  • In the next step, you have to enter the username and password of the Netgear router home page.
  • Navigate to the Advanced section and then proceed to the Administration section.
  • Now, locate and then click on the Firmware Update option. After that, you have to click on the Check button in the new window.
  • If there is any firmware update available, then click on the Yes button.
  • Now, the Netgear router will restart and the firmware will be updated to its latest version. This may take about 10 to 15 minutes.
  • Once the firmware is updated to its latest version, check if you still face the Netgear error 1605.

Wrapping up

To conclude, these are the methods that you can perform to fix the Netgear error 1605 in no time. Moreover, these methods are to the point and are ultimate in resolving this error. However, if you have more queries, then you can use the comments section.

12May/19

Reliable Methods To Resolve The Netgear Error 1628

As we all know that the Netgear router is regarded to be one of the best routers in the recent market but sometimes users face Netgear error 1628. This is a very common error that Netgear router users frequently confront. Basically, the error code 1628 is prompted when you try to connect the router with the Windows device. Even when your modem is not configured properly, you might also encounter the error. In addition, a virus attack can also develop this kind of issue in your device. With this error, you cannot connect your device with the router. Moreover, an outdated version of Windows OS or Router might lead you to this situation.

However, if you are encountering the same issue while using the Netgear router, then it is important to resolve the problem as early as possible. This article will help you in order to eliminate the error code 1628 quickly.

Easy Hacks to Eliminate the Netgear Error 1628

Every problem has some effective solutions. Therefore, in this case, there is no exception. You can fix the Netgear error 1628 with some effective steps. That is why we are here to help you out and provide you some technical solutions in order to solve the error code. Simply go through the discussed solutions and apply them accordingly.

Fix 1: Rename the InstallShield Folder

The first thing that you should try is to rename the installation folder and name it as an InstallShield. This is available under the Programs files. Hence, go through the following steps in order to do this.

Step 1

At first, press the Windows key and the E key at the same time and hold it to open the Windows Explorer or File Explorer on your device.

Step 2

Now, expand the My computer which is located on the right side of the window. Then, go to the following location named like C:\Program Files\Common Files.

Step 3

After that, locate the Install Shield folder and right-click on it. Select Rename from the list. Next, change the folder name for example change from InstallShield to InstallShieldOLD and then hit the Enter button.

Step 4

Finally, install and then use the application on your device and try to connect the network and check whether it is working or not.

Fix 2: Start the Windows in Safe Mode

Another troubleshooting method is to run the Windows in the Safe Mode. If you have the third party installed on your device, it might prevent to connect the internet connection and you will not be able to access any web pages as well. In order to resolve the issue, start the Windows in the Safe Mode. To start the Windows in the Safe Mode, go through the following steps which are stated in the section below.

Step 1

At first, switch off the system and the printer as well. Wait for a while and press the power button to turn on the device. When the System is awake, press the Esc key continuously until a list of the menu will pop-up on the system screen.

Step 2

Select the Safe Mode option from the list and hit the Enter button. Now your PC will open in the Safe Mode. After that, try to plug in the Netgear router and check whether it is working properly or not.

Fix 3: Disable the AntiVirus

Antivirus can block restrictions to a lot of processes in the system. Therefore, this can very well trigger the error code 1628. So, it will be best if you just disable the antivirus program. To do this, you need to go to the Settings option of the antivirus software. Once you are in that window, find out the Turn on/off the antivirus option. Once you find it, simply click on the Turn off the antivirus option using the toggle switch.

When you are done with this step, try to connect to the internet with the through the Netgear router and the error code gets resolved.

Fix 4: Update the Windows Operating System

Sometimes, the error 1628 can occur if you are using an outdated version of Windows Operating System. Hence, you need to try to update the OS and check the status of the error code. Therefore, follow the steps that are described in the following section in order to update the OS and fix the issue.

At first, go to the Windows main screen and tap on the Start menu. After that, type Settings in the search bar and hit the Enter button. Now, choose the Update and Security option from the Settings tab. A new window will pop-up on the system screen. Then, press the Check for the Update option to verify whether any suitable update available for your Windows version. If yes, then download the latest version and install it on your computer.

Once the entire process is completed, restart the system to run all the new changes. Now check the Netgear error 1628 gets resolved.

Fix 5: Upgrade the Driver for your Modem

If the above-discussed solutions do not help you to resolve the issue, then you need to upgrade the Netgear modem. Hence, go through the steps which are mentioned in the section below.

Step 1

At first, press the Start button and type device manager in the search bar. Press the Enter button to open the Device Manager option on your device.

Step 2

Expand the category and search for the Network Adapter section and right-click on it. Then choose the Update Driver option from the list. It will automatically find the updated driver.

Step 3

In some cases, if the Windows is unable to find the updated version of the modem, then simply visit the Manufacturer’s website and enter the model name and number of the Netgear router. There will find the updated driver easily.

Step 4

Download the latest version and install it on your device. Lastly, restart the system and reconnect the router to check it is working properly or not.

Fix 6: Turn Off the Auto-Turning Features

Firstly, press the Windows Start button and then tap on the Search bar. In the search box, type cmd and hit the Enter button to expand the Command Prompt window. Now, right-click on the option and select the Run as Administrator to start the Window. Now type the following command in the command box and press the Enter button.

Netsh interface TCP set global autotuning disabled

When you are done with this step, try to connect the internet connection and see if it works.

Last Words

Hope that with all these solutions which are described in the above section are helpful in order to resolve the Netgear error 1628 in the proper way. Furthermore, if you are encountering any kind of difficulties while performing these steps, simply leave a comment in the comment section provided in the below.

10May/19

Troubleshoot Can’t Login To Netgear Router Error With Easy Hacks

Imagine a situation where you have some urgent task and suddenly you check that you are unable to login to your Netgear Router. Doesn’t it become quite frustrating? Yes, this is one of the most common issues encountered by the Netgear router user. However, this problem arises for a number of reasons such as forgetting the login username and password. Sometimes, the problem may also occur due to some misconfiguration with your router.

Therefore, If you are encountering can’t login to Netgear router error, then this article is for you. Through this guide, we have tried to present all the possible solution that can help you to get rid off the issue. So, let’s start to read the upcoming part of the article to know the details on it.

Effective Solutions on Can’t Access Netgear Router:

Now, if you are unaware of how to resolve this error on your own, then the following steps will definitely guide you in the best way possible. Go through the steps that are written in the following part of the article, to know the details on it.

Solution 1: Reset the Netgear Router

Resetting the Netgear router might help you to resolve the error effectively. Now, to do so, follow these steps.

  1. At first, you will need to detach the Netgear router from its modem.
  2. Then, press and hold the Reset button of your router for a few minutes. Keep holding the button until the LED light flashes.
  3. Once the LED light is turned on, now release the button. Then, wait for a few minutes to Restart the system properly.
  4. After that, connect a computer with your Netgear router. And open your preferred browser and visit the official website of the browser.
  5. Now, a pop up will appear on your screen while confirming your task. Click on the Yes button to continue with it.
  6. Thereafter, you will need to choose the router mode from the next page.
  7. Then, click on the Yes button to turn off the Wi-Fi modem router.
  8. Furthermore, you will need to proceed with the next step by following the onscreen instructions. Then, check if the problem is resolved or not.

Solution 2: Change the Admin Password of the Netgear Router

You can also get rid of the problem by changing the password of the Netgear router. If the procedure to change the password of Netgear is unknown to you, then you should follow the steps that are written below.

  1. At first, open your preferred browser and visit the official website of the manufacturer.
  2. After, opening the website the login Window will appear on your screen.
  3. Now, login with the Administrative username and password.
  4. Then, click on the Advanced option, and then select the Administrative tab. Thereafter, click on the Set Password option.
  5. After that, write down your existing password.
  6. Then, enter your new password and again re-enter the new password.
  7. Now, click on the Enable Password Recovery option. This will help you to recover your password in the future.
  8. Click on the Apply button to save all the changes that you have made.

Solution 3: Log in with the Router and Derive the Settings

If you can’t log in to Netgear genie, then you should try to change the router settings. The following steps will help you to change the settings of your router.

  1. At first, your preferred web browser. Then, visit the official website of the browser and write down the default IP address.
  2. Thereafter, press the Enter button or click on the Search bar.
  3. Then, enter your name and password in the login Window.
  4. After that, click on the OK or Log in button and follow the onscreen prompts. And if you find any misconfiguration in the settings option, then you should change the settings of the router as per requirement.

Solution 4: Configure the Router for Cable Internet Connection with Smart Wizard

If all the methods have failed to resolve the error can’t login to netgear genie then, you should try to configure the router for cable internet connection with a Smart Wizard. The steps which are next to you will help you to do so, go through it.

  1. Connect your Netgear router with the modem through an internet cable. Also, you need to connect your computer with a LAN port.
  2. Turn off and turn on all the devices such as computer, router, and broadband or cable modem. And let’s boot up the devices.
  3. After that, open your preferred browser and write down the IP address in the Search bar. And hit the Enter button.
  4. Then, log in to the router with the admin username and password. If you have forgotten your admin password, then you should try to perform a factory reset in your system.
  5. Thereafter, click on the Setup Wizard option, now the Setup Wizard screen will appear on your screen. Then, click on the Yes button and select the Next option.
  6. Furthermore, you will need to proceed with the next step by clicking on the Next button from the Dynamic IP section.
  7. Then, click on the Router Status option that you can find under the Maintenance section. Now, check if the problem is resolved or not.  

Wrapping it up

Through this article, we have tried to present all the possible solutions that can help you to fix your problem with can’t login to Netgear router. Try the steps that we have mentioned in the entire part of the article, to get rid of the issue without further hassle. If you have any more queries regarding this topic, then you can comment us down to the comment section.

08May/19

Netgear Readyshare Not Working: Resolve This Issue With Some Premium Hacks

Netgear is one of the most preferred router brands throughout the globe. This router brand successfully left behind its competitors by providing exceptional features and superior connectivity. But still, it is not free from occasional glitches. Netgear Readyshare not working is a common bug which is often encountered by several Netgear users while trying to connect the router to the system. Readyshare is a rare feature of Netgear router that helps the users to connect flash drives or hard drives with the router. The drive which is attached with the router will be available for those users who are currently working on the internet or on this network. Most of the USB drives of the router runs with the help of this Readyshare feature. But, sometimes this feature stops to work properly due to some unusual reasons.

If you are on the same condition, then nothing to get worried about this. Here in this article, we are going to present some amazing hacks which can help you to get rid of this issue. Hence, you are advised to go through the guide given below.

Know the Probable Causes of Netgear Readyshare Not Working Issue:

Before going to perform the troubleshooting hacks, it’s better to identify the specific reasons behind this issue. It’s also become easy to troubleshoot a problem after knowing the causes behind it. Hence, have a look at the reasons pointed below:

  • You can face this issue due to the bad network signal.
  • If the firmware of the router gets outdated, then it might be the reason behind this issue.
  • If you are using an outdated version of Windows Operating System, then also you can face this problem.
  • Sometimes, if you turn on the SMB or Server Message Block feature of the Windows Operating System mistakenly, then it can also lead to this problem.  

Now, you are aware of the root causes behind this error. Hence, now you just need some hacks to fix this issue.

Easy Tips and Tricks to Fix Netgear Readyshare Not Working Issue:

There are a lot of easy and simple tricks to fix the Netgear Readyshare USB not working’ issue. Hence, stick to the troubleshooting hacks explained below:

Procedure 1: Update the Router Firmware

If you are using an obsolete firmware of the router, then there might be chances of encountering this kind of problem. Hence, updating the router’s firmware is one of the best hacks to solve this issue. To update the firmware of your Netgear router, you should perform the steps listed follows:

Step 1

At first, open the default web browser of your computer. Then, visit the official website of Netgear. On the Netgear website, you should navigate to the search field and enter the model number of your router to search for the most compatible firmware of the router.

Step 2

When you find the latest firmware of the router, then tap on the ‘Download Now’ link to download the firmware.

Step 3

After that, open a new tab and enter the IP address of your router in the address bar. Hit the Enter button to go to the next page. It will open the setup page of the router. Now, you have to enter the login credentials in the specific field and tap on the ‘Log n’ option. It will navigate you to the configuration page of your Netgear router.

Step 4

Move the cursor left pane of the Configuration window and tap on the ‘Administration’ section. Now, you should navigate to the ‘Advanced’ tab and tap on the ‘Firmware Update’ option. In some of the particular Netgear router, you will see the ‘Maintenance’ tab instead of the ‘Advanced’ tab. Then, you should Tap on the ‘Router Update’ link by going to the ‘Maintenance’ tab.

Step 5

After that, tap on the ‘Choose File’ option and click twice on the ‘Download’ button. Once the downloading process completes, you should tap on the ‘Upload’ button to upload the firmware of the router.

Now, restart the router to apply the changes. Then, you should try to use the USB drive to check whether the issue still appears or not. If the problem persists, then you should move on to further solutions.

Procedure 2: Update the Windows Operating System

You can also fix the Netgear Readyshare USB not working issue by updating Windows OS. In order to update the Operating System, you should perform the steps provided below:

Step 1

First, hit the I and Windows key both at the same time from the keyboard to open the Settings window. Else, you can move the cursor to the left bottom of the screen and tap on the Start menu. Then, tap on the gear-shaped Settings icon from the Start menu.

Step 2

On the Settings window, you will see the ‘Update & Security’ category. Tap on it.

Step 3

Go to the left pane of the ‘Update & Security’ window and tap on the ‘Windows Update’ option. Now, you have to tap on the ‘Check for updates’ option from the ‘Windows Update’ window. As a result, it will start to search for the available update. If an update is available there, then it will start to download it automatically.  

Step 4

After finishing the updating process, it will navigate you to the next window. Here you will see a complete list of all the updates. To complete this procedure, you have to tap on the ‘Install all’ option. It will start the installation procedure. Wait for a few minutes until the installation process is running. Once the process completes, tap on the ‘Finish’ button and exit from the current window.

Now, restart the system. Then, you have to try to connect a USB flash drive to the router to check if the reasdyshare feature is working properly or not. If you see that the problem is still unresolved, then go to the next method discussed below.

Procedure 3: Disable the SMBv1 by Using Windows Registry

According to some users, they have fixed the Netgear Readyshare not working issue by deactivating the SMBv1 using the Windows Registry. To disable the Server Message Block feature on the system, you should follow the steps mentioned below:

Step 1

At first, open the Run dialog box by pressing the R and Windows key both at the same time from the keyboard. Now, type ‘regedir.msc’ in the Run dialog box and hit the Enter key from the keyboard to go to the ‘Registry Editor’ window.

Step 2

On the next window, move the cursor to the Address bar. Then, type the key ‘HKEY_LOCAL MACHINE\SYSTEM\CurrentControlSet\Services\LanmanServer\Parameters’ and hit the Enter key from the keyboard to go to the next page.

Step 3

Now, look at the right pane of the screen and click twice on the ‘SMB1’ key. As a result, it will navigate you to the ‘DWORDSMB1’ window.

Step 4

Look at the upper right side of the next window and tap on the ‘Value’ label. Now, you will see two options. They are ‘zero’ and ‘one’. Here the ‘zero’ value indicates the ‘Disabled’ option and ‘one’ indicates the ‘Enabled’ option. Hence, here you have to change the value to ‘zero.’

After that, you have to close the window and restart the system to apply the changes. Now, you should try to use the USB drive to check whether the Readyshare features started to work.

Final Recommendation

In the above guide, we have discussed some of the possible methods to fix the Netgear Readyshare not working issue. It is our hope that if you implement the above ways in their respective order, then it will surely assist you to put an end to this bug. After successfully performing the above ways if your concern is still unresolved, then you should seek help from a tech expert for further assistance. In addition, you can also share your queries and valuable feedback through the comment box given at the end of this post.

08May/19

Netgear Parental Controls Not Working: Fix This Issue To Safeguard Privacy For Your Netgear Router

The Parental control settings on the Netgear router can stop working due to some technical error. When this happens, it can be a problematic situation for the parents who have enabled this feature on their routers. Parental control allows them to monitor the ongoing activities in Netgear Genie and block access to the Internet for unauthorized users, especially for children. So, to ensure that the parental control filter starts to work again, it requires some technical hacks from the Netgear specialists. Now, to learn why your Netgear parental controls not working on the router, you can check this article. Here, you can also refer to the troubleshooting methods in order to enable this parent control feature on the Netgear router.

Why Netgear Parental Controls Not Working on your Router?

If the parental monitoring settings is not responding for the routing device, it can happen due to multiple reasons. But, unless you understand the underlying reasons that can disable this security feature, you can’t enable it. So, let’s discuss a few common causes which can result in the Netgear parental controls not working issue.

Possible Causes to Block ‘Parental Controls’ in Netgear Genie

Sometimes, the users forget to turn on the tab for parental controls on their Netgear routers. Hence, this can be a possible reason why Netgear Genie is not showing the parental supervision feature anymore.

If you are connecting Netgear router to a PC that is already running a cybersecurity program, this error can pop up. Basically, this happens when such a software interferes with the drivers of the Netgear device.

Often, the portal of Open DNS can become inaccessible because of various issues in the main server. Hence, it can affect the router, which can also result in blocking the parental supervision tab for the users.

If the installation process for Netgear Live Parental Controls is incomplete, it can lead to Netgear Genie parental controls not working issue. Similarly, any corrupted files in the Netgear setup can also be responsible for turning off parental monitoring.

Effective Solutions to Apply If Netgear Parental Controls Not Working While Using the Router:

If you notice that the Parental Controls feature is not responding on your Netgear router, it can be due to both software and hardware reasons. But, you can try some of the effective methods to make sure that Netgear Live Parental Controls is working properly. So, let’s discuss a few hacks which can turn on the parental monitoring feature on your Netgear device.

Method 1- Remove Old Setup and Re-install Netgear Genie

Somehow, if the current Netgear Genie settings don’t enable the feature of parental supervision, it indicates some error. Hence, you can uninstall the current setup for Netgear Genie and then begin the fresh installation of the router driver.

Step 1

So, your first task is to click on the Windows Start button and open the Search box. Then, find the window for the ‘Control Panel’ and navigate to the ‘Programs and Features’ section.

Next, click on the link for ‘Uninstall a program’ and select the icon for Netgear Genie. After this, hit the ‘Uninstall’ button and wait for Windows to remove the Netgear router program.

On some machines, you will be able to delete the entire setup for Netgear Genie by double-clicking on the uninstall.exe file. Once the software and associated components for this router device are removed, download and install the latest version of the Netgear Genie app.

Step 2

After launching this application, click on ‘Home’ and find the icon for ‘Parental Controls’ from the list of features. Now, in order to set up the Netgear Live Parental Controls, you will have to login by entering the default username and password.

For those who aren’t aware of the credentials for signing into Netgear setup, type ‘admin’ as the username. Also, write ‘password’ in place of the security key for the Netgear Genie. Otherwise, you can get in touch with a router professional to recover your old credentials, if you have changed it in between.

Step 3

As soon as you enter the sign in details, you will notice the popup window for ‘Parental Controls’. Now, click on the ‘Next’ tab, which is present at the bottom-right corner of the Netgear Genie setup page.

Below the ‘Setting up Live Parental Controls’ heading, choose the ‘No, I need to create a free OpenDNS account’ option. After that, hit the ‘Next’ button and enter the details necessary for creating a new profile on the router configuration window.

Step 4

Make sure to choose a unique name for Netgear’s username, so that nobody can guess it quickly. Also, you need to click on the tab for ‘Check availability’ to ensure that if you are selecting a proper username for setting up the Netgear Genie.

Once again, hit the ‘Next’ button and select the filtering level to protect your router network. In case, you want to enable parental controls for blocking the access for your curious children, choose the ‘High’ option for maximum protection.

This is also necessary for blocking adult content websites which can be accessed without ‘Parental Controls’ in Netgear Genie. In addition to this, this setting will prevent access to social networking sites, phishing attacks, illegal, and time-wasting content.

After selecting this feature, click on ‘Next’ and restart your system after exiting the Netgear Genie setup page. Hopefully, you will now observe that the blocked websites are not accessible anymore and ‘Parental Controls’ feature is working again. If the issue remains the same, try the remaining fixes to enable parental monitoring feature in Netgear.

Method 2- Change Custom Settings for Parental Controls

In case the above method fails and your Netgear Genie parental controls not working, customize your security settings. To apply this fix, open the setup page for Netgear Genie router and click on the ‘Parental Controls’ option.

As you hit this tab on the left panel of the window, it will display a ‘Status’ page on the right side. Here, you need to find the ‘Change Custom Settings’ button and click on it.

This will direct to ‘netgear.opendns.com’ where you can type your username and password for accessing your OpenDNS profile. After signing into your Netgear account, click on the ‘Custom’ option below the heading of ‘Modify default filtering level’.

Next, scroll down the page and tick/untick the checkboxes or categories which you want to block/unblock on Netgear. Finally, hit the ‘Save Default Filtering Level’ tab in order to register these changes.

Now, try to access any website that may require parental supervision features and see if it’s blocked by Netgear Genie.

Method 3- Restrict Internet Access with Time Block

The previous methods can be applicable for restricting specific content and adult websites by creating a firewall in Netgear. However, if your children can manage to get access to alternate sites or proxy tools, they may still view them. Hence, enabling a time limiting feature can be a great way to deal with shortcomings of ‘Parental Controls’.

Step-1

In order to try this solution, you will have to develop a new bypass account. So, let’s discuss the steps in order to apply this fix by activating time blocker.

First, open the Setup window of Netgear Genie and follow the steps in method 2 to find ‘Change Custom Settings’. You need to click on this tab and go to the directed page ‘netgear.opendns.com’.

Step-2

Next, you have to select the link for ‘Add a bypass account’ and create an account on mobile or PC having Netgear Genie app. You have to follow proper instructions to develop this profile with a new set of username and password. After verifying the security key, click on the ‘Add account’ tab.

Step-3

You can now select your desired filtering level under the ‘Modify filtering level for Dad’ section. Then click on the ‘Save Filtering Level’ tab and hit the ’Add a time block’ button. Now, select the appropriate value for ‘Time Range’ and return to the setup window for Netgear Genie. Finally, click on the ‘Bypass Login’ tab and double-click on your profile to view the access page. Here, you have to type your password and select the ‘Login’ button to access the feature of Netgear Live Parental Controls.

Somehow, if the Netgear parental controls not working even after applying any of these methods discussed here, you need to consult professionals. Hence, get in touch with a router technician, who can assist in enabling the ‘Parental Controls’ feature in Netgear Genie.

07May/19

Learn What To Do If Netgear wna3100 Keeps Disconnecting

Netgear wna3100 is one of the most popular wireless USB adapters all over the World. Despite its amazing features, it is not free from technical glitches. Netgear wna3100 keeps disconnecting is one of the most common problems that users are encountering these days. This issue generally occurs if the USB driver has not been updated. Sometimes, it can also appear when the USB driver is corrupted or damaged. Most of the users have reported that their Netgear wna3100 keeps disconnecting Windows 10 and as a result, their task gets hampered.

So, if you are also encountering this similar problem then read this article carefully. Here we are going to share easy and different procedures to get rid of this particular issue on the Windows 10 system.

Effective Procedures to Fix the Netgear wna3100 Keeps Disconnecting Error:

Let’s take a look at the section below where we are going to discuss some effective and useful procedures that can help you to solve the error effortlessly. Perform these procedures one by one in order to resolve this problem.

Procedure 1 – Update the USB Driver

The primary solution that you have to perform is the update the USB driver. If the driver is outdated then there are chances that you may encounter this problem on the system. So, it is necessary to update the USB driver to the latest version. To complete this procedure follow the instructions which are mentioned below:

  1. At first, press the Windows Home button and R key together to launch the Run window.
  2. In the Run dialog box, type Device Manager and then click on the OK button or hit the Enter key.
  3. When the Device Manager window opens, take the mouse to the Network Adapter section on the left side panel, select it to expend it.
  4. After that, right click on the USB driver and then select the Update Software Driver option to start the update process.
  5. After completing this process, restart the device and then check if the problem still persists or not.

Procedure 2 – Turn Off the USB Selective Suspend Settings

By turning off the USB selective suspend settings on the system can eliminate the Netgear wna3100 keeps disconnecting problem on your PC. The following steps will help you:

  1. Firstly, hold down the Windows Home key and press the X button to open the WinX menu list and then select the Control Panel application.
  2. From the Control Panel window, double-click on the Hardware and Sound section.
  3. In the Hardware and Sound tab, select it Power Options button.
  4. When the Power Options window opens, click on the Change plan settings button.
  5. After that, you can click on the Change Advanced Power Settings option.
  6. From the Advanced Power Settings window, go to the USB settings, select it to expend it.
  7. After that select the USB selective suspend Settings and then choose the Disable button for both options.
  8. Once you are done with these steps, select the OK button to save it.

Procedure 3 – Disable the WLAN Adapter Suspend

This is an alternative procedure that you can apply on your computer to resolve the Netgear wna3100  keeps disconnecting Windows 10 problem is that disabling the WLAN adapter suspend. Hence, follow these steps:

  1. Right-click on the Windows Home icon to open the WinX menu list.
  2. From that list, you will see the Device Manager application, click on it.
  3. When the Device Manager application opens, go to the Network Adapters and then right-click on the Driver to launch the list.
  4. After that, select the Properties option.
  5. In the Properties window, move the cursor to the Power Management tab and then unmark the Allow the computer to turn off the device to save power button.
  6. After doing this, select the OK button to change the settings.
  7. Restart your PC and then check if the issue still appears or not.

Procedure 4 – Reinstall the Driver

Due to the corrupted driver, you might encounter this problem on your computer. So you have to remove the driver and then install it on the system. To reinstall the driver follow these instructions:

  1. First of all, press the Windows Home key and S key to open the Search Panel.
  2. Type Device Manager in the Search Panel and then hit the Enter button.
  3. From the Device Manager application, go to the left side panel and right click on the Driver and then click on the Remove Device button to uninstall the driver.
  4. Once the driver is uninstalled, you can again install it from the official website of the Netgear.
  5. Go to the Netgear official website and search for the latest version of the Netgear wna3100 and then download it.
  6. Once the download file is completed, install it. To finish the installation process follow the onscreen instructions carefully.
  7. After finishing this, restart your PC and then check if the Netgear wna3100 works perfectly.

Procedure 5 – Perform the Network Troubleshooter

If the previous procedures do not work out properly then you can use this procedure to remove this problem on your computer. By performing the network troubleshooter, you will eliminate this problem from your PC. To do that:

  1. Open the Settings application by pressing the Windows button and I key together.
  2. When the Settings window opens, go to the Update and Security section.
  3. From that section, take the mouse to the Troubleshoot tab on the left side panel, select it.
  4. On the Troubleshoot tab, scroll down the page and find the Network Adapter, select it and then click on the Run the troubleshooter button to begin the process.
  5. Now the system will find the problem and fix it automatically.
  6. Once it gets finished, reboot the system and then check if the problem has been resolved or not.

Hopefully, by now you will get all the information about the Netgear wna3100 keeps disconnecting problem. The procedures mentioned above are very easy and effective ways to solve this problem on your computer. Carefully read this article and do these steps accordingly on your PC to fix this glitch. In case you face any problem to do that then you need to consult with an expert.

07May/19

Netgear DNS Error: Best Hacks At Your Fingertips

The “Netgear DNS Error” can come up, when you try to browse the internet. Usually, when you get this issue, then the full error appears with a message that is the “DNS Server is Not Responding”. This problem can crop up if the DNS server that translates the domain name is unable to give some response. There can be various reasons for this problem. Some of the usual reasons are that if the DNS Server address gets altered, then you can face this issue. Even, due to the unused networks also you can get this problem. Further, if the DNS cache has corrupt information within it, this problem can arise. Moreover, change the MAC address and restart the computer and router.

Methods to Resolve the Netgear DNS Error

This is the section of the article that will help you to rectify the DNS server unavailable issue very easily and efficiently. Hence, follow the guide accurately.

Clear the DNS Cache from the Computer

When the files inside the DNS cache gets corrupted or misplaced somehow, then you can get this error. A DNS cache is a memory that stores information about the websites that you have visited while browsing. Therefore, the best solution to eradicate this error is to remove all the contents within the DNS cache. In order to do this follow the below steps.

  • First, tap on the ‘Cortana’ logo, to open the search area of the Windows.
  • After that, on that blank space,  type the text “command prompt”. Next, from the output of this search,  right-click on the option ‘Command Prompt’ and then choose the suboption from the popup menu that comes up, which will be “Run as administrator”.
  • Now, a new window that has the name ‘Command Prompt’ with a black background and white text will come up.
  • Within this window, type the command – ‘ipconfig /flushdns’ and hit ‘Enter key. This command will remove all the contents inside the DNS cache. Check if this error comes back or not.
  • Now, if you get this problem even after the DNS cache is cleaned then type in the following four commands – ‘ipconfig /registerdns’, ‘ipconfig /release’, ‘ipconfig /renew’, ‘netsh winsock reset’. After each of the commands, press the ‘Enter’ key to execute them.
  • When the execution of all the commands are complete, then reboot the computer and then see if this issue comes back or not.

Change the Addresses of DNS Server

An address of a  DNS server can be collected by the computer automatically. But, if that server does not respond to the request sent by the client computer, then you can face the “Netgear DNS error”. Now, to solve this problem you can change the problematic DNS to a public DNS. To do that, in the correct way, follow the steps underneath.

  • First, tap on both the ‘Windows + S’ keys simultaneously to launch the search popup area. Then, inside that search area, write the text “ncpa.cpl”. When you get the same text under ‘Best Match’ section at the top of the search output, then click on it.
  • This will open a new window, with the name ‘Network Connection’. In it, there will be network adapters on a list.
  • Now, from that list, choose the network that is currently connected to the internet and right-click on it. Next, from the popup menu, locate and choose the option ‘Properties’.
  • This will open a new window, tap on the tab ‘Networking’. Under that tab, there is a list, from it, choose the ‘Internet Protocol Version 4 (TCP/IPv4)’ option.
  • Next, just below the list, go to the right side of that window and click on the ‘Properties’ button. This action will yet again launch a new window, that has a name ‘Internet Protocol Version 4 (TCP/IPv4) Properties’.
  • Within that, window, click on the ‘General’ tab. Now, under that tab, there are two sections. Out of those two, go to the bottom one and then, choose the ‘Use the following DNS server addresses:’ option.
  • After that, type the numbers ‘8.8.8.8’ and ‘8.8.4.4’ within the fields ‘Preferred DNS server:’, ‘Alternate DNS server:’ respectively. Then, below that section, put a checkmark on the option ‘Validate settings upon exit’.
  • Now, tap on the ‘OK’ button and reboot the computer.
  • Finally, inspect whether this problem is still present or not.

Alter the Physical or MAC Address

Sometimes, if the physical address of the computer gets corrupt due to some reason, then you can encounter this issue. So the solution to get rid of this problem is to alter the MAC address of the computer. Here are steps on how can you achieve it.

  • First, press on the combination of ‘Windows + X’ to open the ‘Options Menu’. Next, within that menu, locate the option ‘Windows PowerShell (Admin)’ and choose it.
  • At this moment a ‘UAC’ prompt will come up, in it, select the ‘OK’ button. After that, a new window with the name ‘Administrator: Windows PowerShell’ will come up.
  • Inside that window with a blue background, type a command that follows – ‘ipconfig /all’ and then, press the ‘Enter’ key to run it. This command will showcase the total IP configuration of Windows.
  • From the result of that command, identify the network adapter with which the machine is currently connected and then take a note of the ‘Physical Address’ of the device.
  • Next, go to the ‘Network’ icon present on the bottom right corner of the taskbar, beside the ‘Battery’ and right-click on it. Now, from the popup list, select the ‘Open Network & Internet settings’ option. This will open the ‘Windows Settings’ window with the heading ‘Status’.
  • Inside that window, go to the bottom and select the link ‘Network and Sharing Center’. Then a new ‘Control Panel’ window will come up, that has a similar name as the link which you selected on the last line.
  • Within that window, go to the left panel and then choose the link ‘Change adapter settings’. As soon as you click on that link, a page with a list of network connections will show up.
  • Now, from that list, choose the currently connected network and then, right-click on it, After that, from the popup menu that shows up, locate and then select the ‘Properties’ option.
  • This action will open up a new ‘Properties’ window of the chosen network connection, after that, tap on the ‘Configure’ button. Next, on the ‘Intel Centrino Advanced-N 6200 AGN Properties’ window, select the tab ‘Advanced’. Under that tab, select the option ‘Network Address’ from the ‘Property’ list on the left.
  • Then, go to the right side and then, choose the option ‘Value’. Besides that option, there is a blank space, in it, type in the following address – “408D5C44A795”, Next, click on ‘Ok’ button.
  • At last, restart the computer and see if this error still persists or not.

Deactivate the Networks that are not Currently in Use

When there are more than one network connections present within the computer, then due to conflict of networks you can encounter the “Netgear DNS error”. The solution to resolve this problem is to deactivate the networks that are not in use currently. Follow the steps below, in order to do it.

  • First, press the combination of both the keys ‘Window + R’ all together to launch a new ‘Run’ dialog box.
  • Within that dialog box, write the following text – ‘ncpl.cpl’ on the empty space present on the right side of the label ‘Open:’. Next, tap on the ‘Enter’ key.
  • Now, when a page will come up with a name ‘Network Connection’, in it, locate the network other than currently connected one and right-click on it.
  • After that, from the menu that pops up, choose the ‘Disable’ option.
  • Repeat the third and fourth steps of this method to deactivate all the remaining networks which are unused.
  • Lastly, reboot the computer and check whether this issue comes up or not.

A Process to Restart the Netgear Router and PC

If none of the single methods on this section is unable to correct this issue, then as a last resort, you can simply restart the router and the computer. To do it, follow the lines that are presented beneath.

  • First, on the router press the ‘Power’ button to turn the device off. After that, shut down the computer also.
  • Next, unplug all the cables from the router device and the computer, then wait for a minute or so. When you do this, then the static charge will be released from the router.
  • After that, plug all the cables back to their proper places on the router and the PC. Then, start the router device and then the computer respectively.
  • After that, wait for all the LED light on the router to become static and check if you are getting this error or not.

Conclusion

The “Netgear DNS error” can be easily rectified if you follow all the points on the previous section minutely. But, even after following every step on the above section, still, if you are unable to resolve this glitch, then do not worry at all. Just, give the details about the query that you faced on the comment section present under this article.

07May/19

Convenient Tricks To Eliminate Netgear Error 651 Instantly

Being one of the renowned brands, Netgear mainly deals with manufacturing and selling a variety of connectivity devices. Moreover, it comes with certain appendages mostly for iPods and iPhones. These are network switches, computer cables, USB devices, as well as many other peripherals. The demand of the Netgear router is very high in this market owing to its exclusive features which give you secure connectivity. However, after a considerable period of use, there is a great possibility that the routers will develop certain errors which can disrupt your work.

Recently, users are facing a countless number of issues, among which the Netgear error 651 is the most irritating one. You may think that it is high time when you will require expert guidance to overcome the error without any disparity. Prior to that, go through this user guide to get a good grasp on the effective hacks to eliminate Netgear 651 problem in one go.

Underlying Reasons  for the Netgear Error 651:

Each and every electrical device has some technical glitches. And your Netgear router is no different. As a result, most of the users face it at least once during their lifetime. According to the latest response from the users of the Netgear router, the Netgear Error 651 is one of the most frequent errors that the users face on a daily basis. This issue is quite annoying for the majority of Windows users. You will often face this error when you try to associate the internet with the help of the PPPoE connection. However, there are certainly other reasons that lead to this error. For example, an inappropriate internet and IP configuration, a network card driver issue. As a result, when you get through all these issues, you should resort to the necessary precautions and eliminate this error as quickly as possible. If there is a delay, it might cause extreme problems that can disrupt your entire device which goes out of hand sometimes.

EffectiveTroubleshooting Steps to Evade Connection Failed with Error 651 Error:

The problem associated with the Netgear router is seriously a complicated issue and therefore, requires effective hacks. Hence, we suggest you not to interfere with those complications. Instead, you can resort to the exact troubleshooting steps. However, it is not that much easy to get through with the exact cause and detect the issue. Therefore, go through the rest of the article to know more such tricks in order to fix Netgear error 651.

Reconnect your Router or Other Connecting Devices: 

In case you are using the router, you just need to disable the router and after that, switch it back on after a while say 5 minutes. Moreover, if you use LAN connection, detach the wire and then insert it back again.

Reset TCP/IP on Your PC:

  • First and foremost thing is to launch a command prompt with the help of administrative right.
  • After that, you just have to copy the command “netsh int ip reset reset.log ”
  • Then, you should press the Enter key to complete.
  • Finally, restart your computer. However, if the issue still persists, go through the below steps to prevent Netgear modem error 651.

Recreating Dial-Up Connection:

  • First of all move to the “Network & Sharing Center. Now, you need to press on the “Change Adapter Setting”.
  • After that, right-click your broadband or dial-up connection.
  • Thereafter, you can choose to Create a Copy option.
  • After that, this will make a copy of your previous connection.
  • Now, simply remove the old connection.
  • Finally, you need to redial the new connection.

Boot the Computer in Safe Mode and Disable the Antivirus Software:

  • When the computer is turned on, you need to restart your system.
  • Moreover, when the P.C is turned on press the “F8” key.
  • Then you need to stop tapping once you find the “Advanced Boot Options” menu.
  • If you wish to display your selection, you can use the up/down arrow keys.
  • Using the networking, you can choose Safe Mode. After that, press the Enter key.
  • While you load the drivers, you need to wait for some time.
  • Now, you will find the Welcome Screen.
  • Finally, with the help of an account with Administrator privileges, you need to login to your computer.

After you follow the above steps and still unable to resolve the connection failed with error 651, you can check with the official team.

Final Remark

Hopefully, this article covers all the effective fixes pertaining to the Netgear error 501 issue. If you follow the above steps thoroughly, you can easily resolve the afore-mentioned error in one go. Moreover, you can refer to any user guide for some instant help. Apart from this, if you have any new idea, you can provide that in the comment section.

07May/19

Instant Hacks To Resolve Netgear A6210 Not Detected Error

Netgear routers, despite their high performance, are not error-free. For example, you might encounter Netgear a6210 not detected error at times. This error is mostly encountered with the a6210 model. However, you might face this error with other Netgear router models as well. Once you get stuck with this error, you will not be able to access the internet while it’s connected through the router. This can be a pretty bothersome issue for you as your work will be disrupted if you don’t have internet access on your device.

Therefore, if you want to fix this Netgear glitch on your own, then you can go through this post. Here, in this article, we are going to discuss some easy steps to overcome this matter. But, before going to the fixes, identifying the root causes can be quite difficult for you. So, take a look right below in order to identify the possible reasons behind this Netgear router issue.

Probable Reasons Behind Netgear a6210 Adapter Not Found

There can be a lot of factors responsible for Netgear a6210 not detected issue. Here, we have mentioned only the prominent ones. So, without further delay, let’s have a look at some of the prominent causes of Netgear a6210 not detected issue.

  • The first and foremost reason behind Netgear a6210 not detected issue is a poor internet connection. Therefore, if you are connected to a weak and unstable internet connection, then you will surely encounter this error on your device.
  • There can be a problem with the Netgear router adapter. In such situations, the router is not able to turn on as it doesn’t get the power from the socket. Thus it results in such Netgear error appearing on the screen.
  • The router may not work properly. Such situations usually arise on the rainy season when the water enters the power socket through some leaks, thereby creating a short circuit and thus damaging the router.
  • This Netgear issue can also occur if your device driver is outdated or malfunctioning.
  • Also, faulty or improper configuration of your Netgear router can be another potential cause behind this Netgear a6210 adapter not found error. This problem can be resolved by resetting the configuration.
  • Furthermore, if you have any third-party security software installed on your device, then it blocks the router and may cause this issue. Windows Firewall can also do the same. Sometimes, Windows Firewall restricts the router and as a result, Netgear a6210 not detected issue occurs.

These are the common reasons that can lead to the occurrence of Netgear a6210 not detected issue. Now, let’s move on to the solutions.

What to do When you Find Netgear a6210 Not detected?

Router issues are pretty annoying to the users. However, we have mentioned some easy fixes for this troublesome Netgear a6210 not detected issue. We recommend you apply the fixes one by one in the order given until the issue gets resolved.

Check the Connectivity

Primarily, you have to check the state of the adapters and also of the internet connection. You can also replace the Netgear router adapter with another dummy adapter and check whether the issue still remains or not. After this, you can verify the condition of the Ethernet cable, whether it is fine or not. If there is any kind of damage in the Ethernet cable, then you should contact your service provider and change the cable as early as possible.

Verify the Hardware

The condition of the hardware requires to be verified at regular intervals. At times, it happens that you think the issue is due to any specific detect but it is just a simple hardware glitch. Therefore, whenever you suddenly encounter Netgear a6210 not detected, you can put the Ethernet cable directly in your device and then check whether the issue gets eliminated or not. Now, if you are able to get access to the internet, then be sure that the problem with the router itself. In such circumstances, check if the router is in the warranty period or not. Besides, you can also verify the SATA ports and monitor if it is able to detect any USB device or not.

Check Third-Party Antivirus Program

Sometimes, an antivirus program can conflict with your device and thus resulting in Netgear a6210 not detected error. So, if you face this Netgear router issue after installing an antivirus program on your device, then it is recommended to disable the real-time protection.

Steps to Disable Real-Time Protection:

  • At first, you need to go to the Settings. Now, click on Update And Security. After that, locate the Windows Security. Once you locate it, tap on it. Now, look for the Virus And Threat Protection section.
  • In this section, navigate to Manage Settings. Now, you have to switch the Real-Time Protect to the Disable/Off. And then, follow the on-screen instructions to finish the process.

Once you are done with the above steps, reboot your device. Once your device restarts, check if the Netgear a6210 not detected error is gone or not. In case, you still face the same error, then you should uninstall the antivirus software from your device and check if this helps you to overcome this situation.

Steps to Uninstall Antivirus Software:

  • In the beginning, you need to go to the Start menu and then navigate to the Settings. After that, choose System. Next, you need to locate the “Apps And Features” option that is present in the left pane.
  • Now, choose the device you have to Uninstall or Remove from your system, Once you are done, simply hit the Uninstall button that appears on the display screen.

After performing the above steps, restart your device to apply the new changes. Once your device restarts, you can check if the Netgear a6210 not detected issue has been resolved or not. In case, the issue still persists, then you have to proceed to the methods given below in order to eliminate the issue you are facing.

Reset the Netgear A6210 Router

If the previous method didn’t work for you, then you might need to reset the Netgear a6210 router. Several users claim that after resetting their Netgear router, they find that the issue gets resolved. Therefore, it is recommended to reset the Netgear a6210 router. But, in case, you don’t know how to reset the Netgear a6210 router, then you can carry out the steps that come next.

Step 1:

First, you have to press the Reset button of your Netgear router with a pointing tool such as a paper clip. After that, attach the Ethernet cable in your Netgear router and try to start the Google Chrome or any other web browser you are using. Now, enter “http://192.168.2.1.” in the search engine of your browser.

Step 2:

Now, you will observe the “Router Setup Login” on the screen. On this page, you require to enter the accurate “Username” and the “Password” and then tap on the Login button. After performing this action, the Netgear router widget will open. Thus, you need to provide the proper configuration and when you are done, hit the “Apply Changes” button. Now, you can confirm the process by tapping on the OK button.

Once you are done with the above steps, restart your device to apply the new changes. After restarting your device, check if the Netgear error gets eliminated from your device.

Update the Netgear A6210 Router Driver

After resetting your Netgear a6210 router, if the error code still appears, then you can update the Netgear a6210 router driver. As a simple driver update can resolve various issues including Netgear router a6210 not detected. So, take a look at how to update the Netgear a6210 router from the Device Manager.

Step 1:

First, press and hold the Windows Home key + S key simultaneously on your keyboard. This process will bring up the Search dialog box. Now, write “Device Manager” in the search field and press the Enter button or click on OK. Now, select Device Manager from the top search list in order to open it.

Step 2:

Here, in the Device Manager window, you will see all the drivers which are present in your device. Next, attempt to find the option “Network And Adapter” Once you find it, simply click on it and then expand the option.

Step 3:

Thereafter, you will see your Netgear router model name. Just tap on your router option and choose the option “Update Driver” from the menu list. Wait until the update process gets over. Once the process is over, simply restart your device. And once your device restarts, check whether the issue gets resolved.

Wrapping Up

These are the most trustworthy methods that you can try to resolve the Netgear a6210 not detected issue. Therefore, we highly recommended you to apply each method and find out the way that works best for you. Moreover, if you want to read related topics, stay tuned to our posts.